Tr 069 acs server

To the Cisco IOS Network Management Command Reference. SUMMARY STEPS1. enable 2. configure terminal 3. cwmp agent 4. management server url acs-url 5. management server password [encryption-type | cleartext-password] passwd 6. provision code code-string 7. exit 8. interface type number 9. cwmp wan 10. cwmp wan default 11. exit 12. cwmp agent 13. enable download 14. session retry limit session-count 15. request outstanding request-count 16. parameter change notify interval time-interval 17. end DETAILED STEPS Command or ActionPurposeStep 1 enable Example:Device> enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configure terminal Example:Device# configure terminal Enters global configuration mode. Step 3 cwmp agent Example:Device(config)# cwmp agent Enables TR-069 Agent configuration mode. Step 4 management server url acs-url Example:Device(config-cwmp)# management server url Example:Device(config-cwmp)# management server url Specifies the HTTP/HTTPS URL to reach the ACS. This URL is used by the CPE to establish the TR-069 session with the ACS. Step 5 management server password [encryption-type | cleartext-password] passwd Example:Device(config-cwmp)# management server password 0 cisco Specifies the CPE password that is used in the authentication phase. This password will be provided to the ACS when the CPE is challenged for credential as part of authentication during the session establishment. Step 6 provision code code-string Example:Device(config-cwmp)# provision code ABCD Specifies the provision code to be used by the CPE. Step 7 exit Example:Device(config-cwmp)# exit Exits TR-069 Agent configuration mode and returns to global configuration mode. Step 8 interface type number Example:Device# interface serial 0/0 Enters interface configuration mode. Step 9 cwmp wan Example:Device(config-if)# cwmp wan (Optional) Defines the WAN interfaces on the CPE. Note Any interface without this command is considered a LAN interface by TR-069 protocol. There can be multiple WAN and LAN interfaces configured on the CPE. By default, an ATM interface on the CPE will be considered a WAN interface by the TR-069 protocol. Step 10 cwmp wan default Example:Device(config-if)# cwmp wan default Defines the default WAN interfaces on the CPE device. Note Among the multiple WAN interfaces, there can be only one default WAN interface in which the TR-069 communication could happen. If you try to configure this command on multiple interfaces, only the latest configuration will be active and the previous default WAN interface will become a WAN interface, ensuring only one interface is the default at any point in time. Step 11 exit Example:Device(config-if)# exit Exits interface configuration mode and returns to global configuration mode.

The value in Cisco ISR G2; only one storage path and it is the flash memory. ntp server 100.12.12.1 YES (no archive) YES (configure archive) Prerequisites for the TR-069 Agent The CPE should have an IP address and a WAN connection should be established to access the ACS. Information About the TR-069 AgentTR-069 AgentHTTP Digest Authentication SupportHTTP Cookie Support Per RFC2965Device Gateway Association and Port Mapping SupportTR-069 Agent The TR-069 Agent allows an ACS to provision a CPE or collection of CPEs. The provisioning mechanism includes specific provisioning parameters and a general mechanism for adding vendor-specific provisioning capabilities as needed. The identification mechanisms included in the protocol allow CPE provisioning based either on the requirements of each specific CPE, or on collective criteria such as the CPE vendor, model, software version, or other criteria. The provisioning mechanism allows CPE provisioning at the time of initial connection to the broadband access network and the ability to reprovision at any subsequent time. This includes support for asynchronous ACS-initiated reprovisioning of a CPE. The TR-069 Agent also supports image upgrade, configuration application, file downloads, configuration and log file uploads, and CPE monitoring. Note The TR-069 Agent CPE devices must be set up and enabled for TR-069. An ACS used to communicate with the CPE must be TR-069 compliant in order to enable the TR-069 Agent. RPC Support The following remote procedure calls (RPCs) supported with the TR-069 Agent: Standard RPCs GetRPCMethods SetParameterValues GetParameterValues GetParameterNames SetParameterAttributes GetParameterAttributes AddObject DeleteObject Reboot Download Upload Vendor RPCs X_00000C_SetConfiguration X_00000C_ShowStatus CWMP Vendor Profile Schema The following details the CWMP vendor profile schema: For SetConfiguration, rollback {running-config | startup-config} block of clis separated by newline [\n] character IOS Configuration command 1 IOS Configuration command 2 parameterkey ErrorOption => string with length 64Target => string with length 64 On success, 0 On failure, ClientCWMP fault IOS Configuration command that failedparse_cmd() return value IOS Configuration command that failedparse_cmd() return value For ShowStatus, IOS Exec command 1 IOS Exec command 2 IOS Exec command 3 On success, IOS Exec command 1 output of command 1 IOS Exec command 2 output of command 2 IOS Exec command 3 output of command 3 On failure, ClientCWMP fault HTTP Digest Authentication Support The TR-069 Agent uses HTTP as the transport and needs support for digest authentication from the HTTP client infrastructure. Note This feature is not a TR-069 Agent-exclusive feature and can be used in

FAQ How do I buy the products? You can get products in offline stores or online retailers according to the above sheet. Contact sales if you need special firmware or when you want to buy in bulk. How do I prepare to deploy TR-069 in my network? Deploying TR-069 requires compatible CPE devices and ACS. Tech specialists are needed for the maintenance of ACS. If you simply want to boost your deployment, you may look for Aginet Config. How do I enable auto-configuration on TR-069 devices? Set the ACS address, profile info (username and password) for devices in advance to enable auto-configuration. TP-Link recommends using Aginet Config to deploy the ACS settings efficiently. Does TP-Link offer an official ACS solution for TR-069 products? If you are looking for the ACS solution provided by TP-Link, you may check out Aginet ACS offered by a TP-Link Service Provider. The products supported by Aginet ACS differ from those listed on this page.

Step 12 cwmp agent Example:Device(config)# cwmp agent Enables TR-069 Agent configuration mode. Step 13 enable download Example:Device(config-cwmp)# enable download (Optional) Enables the CPE to permit a software download. By default, this command is disabled. Step 14 session retry limit session-count Example:Device(config-cwmp)# session retry limit 10 (Optional) Sets the session retry count whenever the TR-069 session establishment fails with the ACS. The range for the session count argument is 0 to 15. The default value is 11. Step 15 request outstanding request-count Example:Device(config-cwmp)# request outstanding 6 (Optional) Sets the count for the number of requests that can be sent by CPE to ACS without receiving the acknowledgement. The range for the request count argument is 0 to 10. The default value is 5. Step 16 parameter change notify interval time-interval Example:Device(config-cwmp)# parameter change notify interval 75 (Optional) Sets the time interval, in seconds, for the parameter change notifications. The range for the time interval argument is 15 to 300. The default value is 60. Step 17end Example:Device(config-cwmp)# end Exits TR-069 Agent configuration mode and returns to privileged EXEC mode. What to Do NextProceed to Enabling the TR-069 Agent on the CPE task. Enabling the TR-069 Agent on the CPEBefore You BeginYou must have set up the CPE as specified in the Setting Up the CPE to Communicate with the ACS task. SUMMARY STEPS1. enable 2. configure terminal 3. cwmp agent 4. enable 5. end DETAILED STEPS Command or ActionPurposeStep 1 enable Example:Device> enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configure terminal Example:Device# configure terminal Enters global configuration mode. Step 3 cwmp agent Example:Device(config)# cwmp agent Enables TR-069 Agent configuration mode. Step 4 enable Example:Device(config-cwmp)# enable Enables the CPE to initiate a TR-069 session with the ACS. Step 5end Example:Device(config-cwmp)# end Exits TR-069 Agent configuration mode and returns to privileged EXEC mode. Initiating a TR-069 Agent Session from the ACSBefore You BeginYou must have set up the CPE by using Setting Up the CPE to Communicate with the ACS task and enabled the TR-069 Agent on the CPE by using the Enabling the TR-069 Agent on the CPE task. SUMMARY STEPS1. enable 2. configure terminal 3. cwmp agent 4. connection request username username 5. connection request username [ encryption-type | cleartext-password ] passwd 6. end DETAILED STEPS Command or ActionPurposeStep 1 enable Example:Device> enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configure terminal

Up the CPE to Communicate with the ACSExample: Configuring and Enabling CWMP using the Autoinstall featureExample: Setting Up the CPE to Communicate with the ACS The following example shows how to set up the CPE to communicate with the ACS. The ACS URL is and the password is lab. !configure terminal cwmp agent management server url management server password 0 lab provision code ABCD exit interface ethernet 0/0 cwmp wan cwmp wan default exit cwmp agent enable download session retry limit 12 request outstanding 3 parameter change notify interval 120 !Example: Configuring and Enabling CWMP using the Autoinstall feature The following example shows how to configure CWMP using the autoinstall feature. Use the following set of commands in the network-config file or -config file or router-config file in the TFTP server. No additional manual configuration is required for configuring CWMP on the device. !cwmp agent enable enable download management server password lab management server url connection request username user1 connection request password lab!ip http server!Additional References for TR-069 Agent The following sections provide references related to the TR-069 Agent feature. Related Documents Related Topic Document Title TR-069 Agent commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples Cisco IOS Network Management Command Reference Cisco IOS commands Cisco IOS Master Commands List, All Releases Standards Standard Title No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature. -- MIBs MIB MIBs Link None To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: http:/​/​www.cisco.com/​go/​mibs RFCs RFC Title No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature. -- Technical Assistance Description Link The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. http:/​/​www.cisco.com/​cisco/​web/​support/​index.html Feature Information for TR-069 Agent The following table provides release information about the feature or features described in this module. This table